For safe shut downs, charging warnings, and charging status - Adafruit PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C-Purchased from amazon, https://www.amazon.com/gp/product/B01BMRBTH2/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
Shell used-Gametown® Full Housing Shell Cover Case Pack with Screwdriver for Nintendo Gameboy Classic/Original GB DMG-01 Repair Part-White (pick whatever color you want)-Purchased from amazon, https://www.amazon.com/gp/product/B01K1C2L1C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
Screen used- BW 3.5 Inch TFT LCD Monitor For Car/Automobile – purchased from amazon, https://www.amazon.com/gp/product/B0045IIZKU/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 (side note here is that in order to make this fit nicer, I installed it upside down in the case.
Speak used - uxcell 16pcs 27mm External Magnetic Speaker Loudspeaker 8 Ohm 0.25W, purchased from amazon, https://www.amazon.com/gp/product/B010V4RAAW/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 (do not put ANYTHING on the top of the speaker when you install or it will not work.
Prototyping bread board, I purchased from amazon but it is no longer available at the link.
I used this PCB for the buttons on 1 build, the drill guide is VERY useful for this project. - 4 Button PCB For Gameboy DMG-01DIY Pi Zero Made In USA With Grounds and Hole Guide BY:Atomic Market, purchased at amazon, https://www.amazon.com/gp/product/B01JKJCQVM/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1
L-R buttons- 100 Pcs 6 x 6mm x 9.5mm PCB Momentary Tactile Tact Push Button Switch 4 Pin DIP, purchased at amazon https://www.amazon.com/gp/product/B008420WOA/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
28 Gauge Wire - Ribbon Cable - 10 Wire (15ft), purchased at amazon, https://www.amazon.com/gp/product/B007R9SQQM/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 (I recommend going to a smaller (higher) gauge than 28. 30 or 32 would have made it a lot easer but 28 will do.
Indicator lights, Uxcell a11092800ux0119 Uxcell (Pack of 75), purchased at amazon, https://www.amazon.com/gp/product/B01F0TCXSW/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 (these are totally optional)
Resistors and capicitors (audio), purchased from https://www.taydaelectronics.com Note: heres the guide I used for the audio too! https://sudomod.com/forum/viewtopic.php?t=480
Old Gameboy game cartridge. For aesthetics. Headphone jack, ebay, https://www.ebay.com/itm/3-5mm-Stereo-Female-Socket-Audio-Jack-5Pin-PCB-Panel-Mount-Connector-PJ325-/400959590673
Micro SD card (16 GB minimum)
Female Micro usb Port, (I know I did buy these but I can’t find the link. I bought female micro usb ports to make charging easier.)
I want to say this is the battery that I used, specifically because after taking the shell off it was the perfect fit inside of a gutted Gameboy Game cartridge-https://www.bestbuy.com/site/mycharge-razorplus-4000mah-portable-charger-for-most-usb-enabled-devices-silver/6292246.p?skuId=6292246
3d printed button wells-http://market.sudomod.com/3d-printed-gbz-button-wells/
Extra buttons-https://www.retromodding.com/collections/gameboy
Screw bracket-http://market.sudomod.com/3d-printed-gbz-screw-bracket/
I got A LOT of buttons, glass screen shields, the other three builds button PCBs, some stickers, seriously a lot of stuff from https://store.kitsch-bent.com/ his store is unfortunately closed as he has had life catch up to him and has some shit to attend to. If he comes back online show him some love.
Stuff I got from kitsch PCB board with LR input points Buttons for X/Y (you can opt to just get replacement snes or an extra set of Gameboy buttons. Glass screen that fit the GB shell after removing extra plastic
And obviously you should have a pi zero/w as well a shit ton of patience.
For safe shut downs, charging warnings, and charging status - Adafruit PowerBoost 1000 Charger - Rechargeable 5V Lipo USB Boost @ 1A - 1000C-Purchased from amazon, https://www.amazon.com/gp/product/B01BMRBTH2/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
Shell used-Gametown® Full Housing Shell Cover Case Pack with Screwdriver for Nintendo Gameboy Classic/Original GB DMG-01 Repair Part-White (pick whatever color you want)-Purchased from amazon, https://www.amazon.com/gp/product/B01K1C2L1C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
Screen used- BW 3.5 Inch TFT LCD Monitor For Car/Automobile – purchased from amazon, https://www.amazon.com/gp/product/B0045IIZKU/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 (side note here is that in order to make this fit nicer, I installed it upside down in the case.
Speak used - uxcell 16pcs 27mm External Magnetic Speaker Loudspeaker 8 Ohm 0.25W, purchased from amazon, https://www.amazon.com/gp/product/B010V4RAAW/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 (do not put ANYTHING on the top of the speaker when you install or it will not work.
Prototyping bread board, I purchased from amazon but it is no longer available at the link.
I used this PCB for the buttons on 1 build, the drill guide is VERY useful for this project. - 4 Button PCB For Gameboy DMG-01DIY Pi Zero Made In USA With Grounds and Hole Guide BY:Atomic Market, purchased at amazon, https://www.amazon.com/gp/product/B01JKJCQVM/ref=ppx_yo_dt_b_asin_title_o07_s00?ie=UTF8&psc=1
L-R buttons- 100 Pcs 6 x 6mm x 9.5mm PCB Momentary Tactile Tact Push Button Switch 4 Pin DIP, purchased at amazon https://www.amazon.com/gp/product/B008420WOA/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
28 Gauge Wire - Ribbon Cable - 10 Wire (15ft), purchased at amazon, https://www.amazon.com/gp/product/B007R9SQQM/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 (I recommend going to a smaller (higher) gauge than 28. 30 or 32 would have made it a lot easer but 28 will do.
Indicator lights, Uxcell a11092800ux0119 Uxcell (Pack of 75), purchased at amazon, https://www.amazon.com/gp/product/B01F0TCXSW/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 (these are totally optional)
Resistors and capicitors (audio), purchased from https://www.taydaelectronics.com Note: heres the guide I used for the audio too! https://sudomod.com/forum/viewtopic.php?t=480
Old Gameboy game cartridge. For aesthetics. Headphone jack, ebay, https://www.ebay.com/itm/3-5mm-Stereo-Female-Socket-Audio-Jack-5Pin-PCB-Panel-Mount-Connector-PJ325-/400959590673
Micro SD card (16 GB minimum)
Female Micro usb Port, (I know I did buy these but I can’t find the link. I bought female micro usb ports to make charging easier.)
I want to say this is the battery that I used, specifically because after taking the shell off it was the perfect fit inside of a gutted Gameboy Game cartridge-https://www.bestbuy.com/site/mycharge-razorplus-4000mah-portable-charger-for-most-usb-enabled-devices-silver/6292246.p?skuId=6292246
3d printed button wells-http://market.sudomod.com/3d-printed-gbz-button-wells/
Extra buttons-https://www.retromodding.com/collections/gameboy
Screw bracket-http://market.sudomod.com/3d-printed-gbz-screw-bracket/
I got A LOT of buttons, glass screen shields, the other three builds button PCBs, some stickers, seriously a lot of stuff from https://store.kitsch-bent.com/ his store is unfortunately closed as he has had life catch up to him and has some shit to attend to. If he comes back online show him some love.
Stuff I got from kitsch PCB board with LR input points Buttons for X/Y (you can opt to just get replacement snes or an extra set of Gameboy buttons. Glass screen that fit the GB shell after removing extra plastic
And obviously you should have a pi zero/w as well a shit ton of patience.